Domain - Injection Stretch-Blow Moulding
TOP > Manufacturing > Plastics Processing Technology > Injection Stretch-Blow Moulding
| 0 Qualifications | 8 Assessment Standards (8 Units) | View Education Organisations with Consent to Assess |
Qualifications Domain-full
No qualifications currently registered at this level. Also check fields and sub-fields.
Assessment Standards
Hide education organisations, CMR & purpose »
Level 1
Perform basic process operations for injection stretch-blow moulding
This standard has expired and is no longer available.
Version 6
15206 Unit Standard 5 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to: identify and take precautions against operation hazards; perform basic process operations; and demonstrate knowledge of scrap material granulating. This unit standard is to enable entry level people to perform basic process operations in an injection stretch-blow moulding operation.
Standard-setting body:
Level 3
Operate injection stretch-blow moulding equipment
Version 6
15207 Unit Standard 5 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to: demonstrate knowledge of the construction of injection stretch-blow moulding equipment; start up and shut down injection stretch-blow moulding equipment and ancillary equipment that have been pre-set; and operate an injection stretch-blow moulding process.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Set and run the injection stretch-blow moulding production process
Version 6
15208 Unit Standard 10 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to: demonstrate knowledge of the operation of injection stretch-blow moulding equipment; set, control and monitor the production process for a repeat run; perform a material or colour changeover on the moulding equipment; and identify, correct and report routine product moulding faults.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Service tooling for injection stretch-blow moulding
Version 6
15211 Unit Standard 5 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to demonstrate knowledge of the construction and operation of workplace tooling for injection stretch-blow moulding, and perform simple servicing of tooling for injection stretch-blow moulding.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Level 4
Trial and optimise the single stage injection stretch-blow moulding production process
This standard has expired and is no longer available.
Version 6
15209 Unit Standard 12 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to trial tooling in specified injection stretch-blow moulding equipment, and start up the process for an initial production run.
Standard-setting body:
Trial and optimise the two stage injection stretch-blow moulding production process
This standard has expired and is no longer available.
Version 6
15210 Unit Standard 16 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to trial tooling in specified injection stretch-blow moulding equipment, and start up the process for an initial production run.
Standard-setting body:
Demonstrate knowledge and carry out routine maintenance of preform injection moulds
Version 6
15212 Unit Standard 15 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to demonstrate knowledge of the construction and operation of a preform injection mould, and carry out routine maintenance on a preform injection mould in the machine.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Set up tooling for injection stretch-blow moulding
Version 6
15213 Unit Standard 6 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to remove, fit and set a preform injection mould for injection blow moulding; and remove, fit and set blow moulds for a container.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Data as at 2025-05-01 23:01:07.45