Domain - Injection Moulding
TOP > Manufacturing > Plastics Processing Technology > Injection Moulding
| 0 Qualifications | 14 Assessment Standards (14 Units) | View Education Organisations with Consent to Assess |
Qualifications Domain-full
No qualifications currently registered at this level. Also check fields and sub-fields.
Assessment Standards
Hide education organisations, CMR & purpose »
Level 1
Perform process operations for injection moulding
Version 6
252 Unit Standard 4 Credits
View Education Organisations with Consent to Assess »
This unit standard is designed to enable entry-level people to perform process operations in an injection moulding operation. People credited with this unit standard are able to, for injection moulding: identify operation hazards and take precautions; describe the injection moulding process cycle; perform process operations; and demonstrate knowledge of waste material recycling and/or processing.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Level 2
Operate the injection moulding machine
This standard has expired and is no longer available.
Version 6
253 Unit Standard 6 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to: demonstrate knowledge of the construction of an injection moulding machine; start up and shut down an injection moulding machine and ancillary equipment that have been pre-set; and operate an injection moulding process.
Standard-setting body:
Run and monitor the injection moulding production process
This standard has expired and is no longer available.
Version 6
254 Unit Standard 9 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to: apply and monitor injection machine settings; perform a material or colour changeover on the moulding machine; and identify and correct routine product moulding faults.
Standard-setting body:
Set up simple moulds for injection moulding
This standard has expired and is no longer available.
Version 6
256 Unit Standard 8 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to remove, fit, and set simple injection moulds; and select, set up, and operate ancillary equipment.
Standard-setting body:
Service simple moulds for injection moulding
This standard has expired and is no longer available.
Version 6
258 Unit Standard 6 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to: demonstrate knowledge of the construction and operation of simple injection moulds; remove a jammed moulding; and perform simple mould servicing.
Standard-setting body:
Service advanced moulds for injection moulding
This standard has expired and is no longer available.
Version 6
259 Unit Standard 4 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to demonstrate knowledge of the construction and operation of advanced injection moulds, and service advanced moulds.
Standard-setting body:
Level 3
Control and optimise the injection moulding production process
Version 6
255 Unit Standard 12 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to: demonstrate knowledge of, and control the injection moulding process for a repeat production run; trial a simple mould in a specified injection moulding machine; and start up the moulding process for an initial production run.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Set up advanced moulds for injection moulding
This standard has expired and is no longer available.
Version 5 This unit standard has been replaced by unit standard 27925 and unit standard 27926.
257 Unit Standard 7 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to remove, fit, and set advanced injection moulds; and remove and refit an injection moulding machine screw.
Standard-setting body:
Remove and refit an injection moulding machine screw
This standard has expired and is no longer available.
Version 2 This unit standard and unit standard 27926 replaced unit standard 257.
27925 Unit Standard 3 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to remove and refit an injection moulding machine screw.
Standard-setting body:
Set up advanced moulds for injection moulding
Version 2 This unit standard and unit standard 27925 replaced unit standard 257.
27926 Unit Standard 7 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to: remove, fit, and set advanced injection moulds; and select, set up, and operate ancillary equipment.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Carry out routine service of injection moulding equipment
Version 1
29515 Unit Standard 5 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to: demonstrate knowledge of the construction and operation of injection moulds; remove a jammed moulding and continue production; and perform routine injection mould servicing.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Level 4
Service and maintain a complex mould for injection moulding
Version 6
260 Unit Standard 10 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to: demonstrate knowledge of the construction and operation of complex injection moulds; use engineering drawings to interpret complex mould operation and construction; and service complex moulds and describe potential problems.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Trial advanced injection moulds
This standard has expired and is no longer available.
Version 5
9712 Unit Standard 6 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to: prepare for trial; set mould and machine; and trial and evaluate an advanced injection mould.
Standard-setting body:
Set and remove complex injection moulds
Version 5
9713 Unit Standard 5 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to: set complex injection moulds; verify machine, mould and ancillary equipment functions; and remove complex injection moulds.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Data as at 2025-05-01 23:01:07.45