Domain - Extrusion Blow Moulding
TOP > Manufacturing > Plastics Processing Technology > Extrusion Blow Moulding
| 0 Qualifications | 11 Assessment Standards (11 Units) | View Education Organisations with Consent to Assess |
Qualifications Domain-full
No qualifications currently registered at this level. Also check fields and sub-fields.
Assessment Standards
Hide education organisations, CMR & purpose »
Level 1
Perform process operations for extrusion blow moulding
This standard has expired and is no longer available.
Version 6
295 Unit Standard 4 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to: identify and take precautions against operation hazards; perform process operations; and demonstrate knowledge of scrap and waste material and granulating scrap material in accordance with enterprise procedures. This unit standard is designed to enable entry level people to perform process operations in an extrusion blow moulding operation.
Standard-setting body:
Level 2
Service a simple mould for extrusion blow moulding
Version 6
299 Unit Standard 4 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to: identify the components of simple extrusion blow moulds for extrusion blow moulding; and perform servicing of a simple extrusion blow mould, blow pin, and extrusion pin and die.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Service an advanced or complex mould for extrusion blow moulding
Version 6
300 Unit Standard 8 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to: identify the components of an advanced or complex extrusion blow mould; and perform servicing of an advanced or complex extrusion blow mould, blow pin, and extrusion pin and die.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Level 3
Remove and fit an extrusion blow moulding die head assembly and an extruder screw
This standard has expired and is no longer available.
Version 2
27922 Unit Standard 6 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to remove and fit: an extrusion blow moulding die head assembly; and an extrusion blow moulding machine extruder screw.
Standard-setting body:
Operate an extrusion blow moulding machine
Version 6
296 Unit Standard 5 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to demonstrate knowledge of the main components of an extrusion blow moulding machine; start up and shut down an extrusion blow moulding machine and ancillary equipment that have been pre-set; and demonstrate knowledge of, and operate an extrusion blow moulding process.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Run and monitor the extrusion blow moulding production process
Version 6
297 Unit Standard 10 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to: demonstrate knowledge of the operation of an extrusion blow moulding machine; apply and monitor extrusion blow moulding machine settings; perform a material or colour changeover on the extrusion blow moulding machine; and identify and correct routine product moulding faults.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Control and trial the extrusion blow moulding process for a simple extrusion blow mould
Version 6
298 Unit Standard 5 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to: control a production run for the extrusion blow moulding process using a simple extrusion blow mould; trial a simple mould or process in a specified extrusion blow moulding machine; and start up the moulding process for an initial production run of the trialled mould.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Set up simple moulds and ancillary equipment for extrusion blow moulding
Version 6
302 Unit Standard 8 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to remove, fit and set up simple extrusion blow moulds; and set up ancillary equipment for extrusion blow moulding.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Level 4
Service a die head for extrusion blow moulding
Version 6
301 Unit Standard 10 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to: demonstrate knowledge of the components and operation of extrusion blow moulding die heads, extrusion blow moulding accumulator die heads, and parison control units; and service an extrusion blow moulding die head.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Set up and start up an extrusion blow moulding machine to run advanced or complex moulds
Version 6
303 Unit Standard 5 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to: remove, fit and set an advanced or complex extrusion blow mould; demonstrate knowledge of automatic transfer and ejection of extrusion blow mouldings; and set up and start up the extrusion blow moulding machine.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Trial and evaluate an advanced or complex extrusion blow mould or moulding process
This standard has expired and is no longer available.
Version 5
9714 Unit Standard 8 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to: prepare for trial; set mould and machine; and trial and evaluate an advanced or complex extrusion blow mould or moulding process.
Standard-setting body:
Data as at 2024-05-08 23:01:05.65