Domain - Engineering - Fabrication
TOP > Engineering and Technology > Mechanical Engineering > Engineering - Fabrication
| 0 Qualifications | 50 Assessment Standards (50 Units) | View Education Organisations with Consent to Assess |
Qualifications Domain-full
No qualifications currently registered at this level. Also check fields and sub-fields.
Assessment Standards
Hide education organisations, CMR & purpose »
Level 2
Calculate lengths, areas and mass of engineering fabrication materials
This standard has expired and is no longer available.
Version 3
16954 Unit Standard 4 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to calculate the lengths of materials required for fabrication, and determine the areas and mass of materials used in fabrication.
Standard-setting body:
Lay out and mark off regular fabrication shapes under supervision
Version 7
2414 Unit Standard 15 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are, under supervision, able to: prepare for lay out and mark off of materials; make and use templates; mark out surface developments; and verify marking off and laying out of regular fabrication shapes.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Form and shape fabrication materials under supervision
This standard has expired and is no longer available.
Version 8 This unit standard has been replaced by unit standard 25075.
2415 Unit Standard 10 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are, under supervision, able to prepare, perform, and verify the forming and shaping of fabrication materials.
Standard-setting body:
Assemble and mechanically join plate and sheet under supervision
Version 7
2416 Unit Standard 10 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are, under supervision, able to prepare, perform, and verify the assembly and mechanical joining of plate and sheet.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Mechanically cut fabrication materials under supervision
Version 7
2417 Unit Standard 8 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are, under supervision, able to prepare for, perform, and verify the mechanical cutting of materials.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Perform basic fabrication operations under supervision
This standard has expired and is no longer available.
Version 3 This unit standard was replaced by unit standard 29670 and unit standard 29730. This unit standard replaced unit standard 2415.
25075 Unit Standard 12 Credits
View Education Organisations with Consent to Assess »
This unit standard is designed for entry level training in fabrication and related trades, and covers basic fabrication operations. People credited with this unit standard are able to: demonstrate introductory knowledge of fabrication processes, demonstrate knowledge of safe working practices in fabrication, prepare for fabrication of simple objects, fabricate simple objects, and adjust and maintain fabrication machines.
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Demonstrate knowledge of fabrication machinery, materials, and processes
Version 1 This unit standard and unit standard 29730 replaced unit standard 25075.
29670 Unit Standard 3 Credits
View Education Organisations with Consent to Assess »
This is an entry-level unit standard for people working in the mechanical engineering trades involved in the fabrication of metal assemblies. This unit standard is limited to fabrication principles and does not include welding, which is covered in unit standards in the welding domain. People credited with this unit standard are able to demonstrate knowledge of fabrication machinery and machinery components, and common fabrication materials and processes.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Apply good work practices when performing basic fabrication operations under supervision
Version 2 This unit standard and unit standard 29670 replaced unit standard 25075.
29730 Unit Standard 6 Credits
View Education Organisations with Consent to Assess »
This is an entry-level unit standard for people working in mechanical engineering or fabrication that require a basic knowledge of modifying or producing fabricated components. It is concerned with establishing safe use of machines and good work practices, rather than fabricating to close tolerances. This unit standard does not cover principles and methods of welding. People credited with this unit standard are able to apply good work practices under supervision when: preparing for the fabrication of simple objects; fabricating simple objects; and adjusting and maintaining fabrication machines.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Demonstrate and apply knowledge of computerised manufacturing for engineering fabrication
Version 1 This unit standard replaced unit standard 25711.
30473 Unit Standard 4 Credits
View Education Organisations with Consent to Assess »
This entry-level unit standard, intended for off job assessment, is for people working in or preparing to work in engineering fabrication trades. People credited with this unit standard are able to demonstrate knowledge of computerised manufacturing for engineering fabrication, and apply computerised manufacturing to produce a fabrication component.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Level 3
Calculate sizes, mass, volumes, and quantities for fabrication
This standard has expired and is no longer available.
Version 5
16955 Unit Standard 4 Credits
View Education Organisations with Consent to Assess »
This unit standard is for use in training of fabrication trades and covers calculations related to fabrication. People credited with this unit standard are able to: calculate the size, mass, and volume of fabrications; and estimate the quantities of welding consumables required for fabrication.
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Lay out and mark off irregular fabrication shapes under supervision
This standard has expired and is no longer available.
Version 7 This unit standard, unit standard 2422, and unit standard 18107 have been replaced by unit standard 25874 and unit standard 25875.
2418 Unit Standard 15 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are, under supervision, able to: prepare for lay out and mark off of materials; mark out templates, structural sections and surface developments; and verify marking off and laying out of irregular fabrication shapes.
Standard-setting body:
Form and shape sheet, plate, pipe and structural sections using power machines under supervision
This standard has expired and is no longer available.
Version 7 This unit standard and unit standard 2423 have been replaced by unit standard 25698 and unit standard 25699.
2419 Unit Standard 15 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are, under supervision, able to prepare, perform, and verify the forming and shaping of sheet, plate, pipe and structural sections using power machines.
Standard-setting body:
Assemble and mechanically join tube, pipe and sections under supervision
This standard has expired and is no longer available.
Version 7 This unit standard and unit standard 2424 have been replaced by unit standard 25700 and unit standard 25701.
2420 Unit Standard 15 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are, under supervision, able to prepare, perform and verify the assembly and mechanical joining of tube, pipe and sections.
Standard-setting body:
Mechanically cut fabrication materials using powered machinery under supervision
This standard has expired and is no longer available.
Version 7 This unit standard and unit standard 2425 have been replaced by unit standard 25702 and unit standard 25703.
2421 Unit Standard 10 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are, under supervision, able to prepare, perform, and verify the mechanical cutting of fabrication materials using powered machinery.
Standard-setting body:
Develop fabrication patterns manually for simple three-dimensional objects
Version 3
25704 Unit Standard 5 Credits
View Education Organisations with Consent to Assess »
This unit standard is the first in a series of pattern development and marking out unit standards for people training in engineering fabrication trades. People credited with this unit standard are able to develop fabrication patterns manually for simple three-dimensional objects.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Demonstrate and apply knowledge of intermediate light fabrication trade practice
Version 2
25706 Unit Standard 10 Credits
View Education Organisations with Consent to Assess »
This unit standard is for use in intermediate level training of fabrication trades and covers fabrication of components using sheet from 0.4 to 3mm thickness. People credited with this unit standard are able to demonstrate knowledge of intermediate light fabrication trade practice; and fabricate objects for the light fabrication industry.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Demonstrate and apply knowledge of intermediate heavy fabrication trade practice
Version 2
25707 Unit Standard 10 Credits
View Education Organisations with Consent to Assess »
This unit standard is for use in intermediate level training of fabrication trades and covers fabrication of components using plate over 4mm thickness. People credited with this unit standard are able to demonstrate knowledge of intermediate heavy fabrication trade practice; and fabricate objects for the heavy fabrication industry.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Demonstrate knowledge of basic CNC concepts and applications in the fabrication industry
This standard has expired and is no longer available.
Version 2 This unit standard was replaced by unit standard 30473.
25711 Unit Standard 4 Credits
View Education Organisations with Consent to Assess »
This unit standard is for use in training of fabrication trades and covers introductory knowledge of the application of Computer Numerical Control (CNC) in the fabrication industry. People credited with this unit standard are able to demonstrate knowledge of basic CNC concepts and applications of CNC controlled fabrication machines.
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Perform fabrication operations
Version 2
30263 Unit Standard 10 Credits
View Education Organisations with Consent to Assess »
This unit standard is designed for people in fabrication and related trades, and covers fabrication operations. People credited with this unit standard are able to: prepare for fabrication of components, fabricate components, and adjust and maintain fabrication machines.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Cut fabrication materials using hand held power tools
Version 1
30274 Unit Standard 5 Credits
View Education Organisations with Consent to Assess »
This on job unit standard is intended for people training in engineering fabrication related trades. People credited with this unit standard are able to cut fabrication materials using hand held power tools.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Mark out fabrication components using geometrical methods
Version 1 This unit standard replaced unit standard 25874 and unit standard 25875.
30440 Unit Standard 5 Credits
View Education Organisations with Consent to Assess »
This practical unit standard is one in a series of pattern development and marking out unit standards for people training in engineering fabrication trades. People credited with this unit standard are able to prepare for; and mark out fabrication components using geometrical methods; and check work after marking out.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Set up and operate a CNC machine for engineering fabrication
Version 1
30474 Unit Standard 3 Credits
View Education Organisations with Consent to Assess »
This unit standard, intended for on-job assessment, is for people working in or training to work in engineering fabrication roles. People credited with this unit standard are able to set up and operate a CNC fabrication machine.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Level 4
Demonstrate knowledge of force and stress in fabrications
This standard has expired and is no longer available.
Version 5
16956 Unit Standard 4 Credits
View Education Organisations with Consent to Assess »
This unit standard is for use in training of fabrication trades and covers knowledge of forces and stresses in fabrications. People credited with this unit standard are able to demonstrate knowledge of the effects of forces on fabrications; and of stress in fabrications.
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Lay out and mark off complex heavy fabrication shapes
This standard has expired and is no longer available.
Version 3 This unit standard, unit standard 2418, and unit standard 2422 have been replaced by unit standard 25874 and unit standard 25875.
18107 Unit Standard 15 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to: prepare to layout and mark off materials; mark out templates and patterns; lay out and mark off heavy sections; mark off surface developments; and verify laying out and marking off for complex heavy fabrication shapes.
Standard-setting body:
Lay out and mark off complex fabrication shapes
This standard has expired and is no longer available.
Version 6 This unit standard, unit standard 2418, and unit standard 18107 have been replaced by unit standard 25874 and unit standard 25875.
2422 Unit Standard 15 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to: prepare to layout and mark off materials; mark out templates and patterns; lay out and mark off light sections; mark off surface developments; and verify laying out and marking off of materials.
Standard-setting body:
Form and shape fabrication materials
This standard has expired and is no longer available.
Version 7 This unit standard and unit standard 2419 have been replaced by unit standard 25698 and unit standard 25699.
2423 Unit Standard 15 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to prepare, perform, and verify the forming and shaping of fabrication materials.
Standard-setting body:
Assemble and mechanically join sheet, plate, tube, pipe and structural sections
This standard has expired and is no longer available.
Version 6 This unit standard and unit standard 2420 have been replaced by unit standard 25700 and unit standard 25701.
2424 Unit Standard 20 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to prepare, perform, and verify the assembly and mechanical joining of sheet, plate, tube, pipe and structural sections.
Standard-setting body:
Mechanically cut sheet, plate, tube, pipe and structural sections
This standard has expired and is no longer available.
Version 6 This unit standard and unit standard 2421 have been replaced by unit standard 25702 and unit standard 25703.
2425 Unit Standard 10 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to: prepare for mechanical cutting of materials; perform mechanical cutting of materials; and verify mechanical cutting of materials.
Standard-setting body:
Form light fabrication materials
Version 2 This unit standard and unit standard 25699 replaced unit standard 2419 and unit standard 2423.
25698 Unit Standard 20 Credits
View Education Organisations with Consent to Assess »
This workplace unit standard is intended for people training to be engineering light fabricators and covers machine and hand forming. People credited with this unit standard are able to prepare to form, and form light fabrication materials; and inspect work after forming.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Form heavy fabrication materials
Version 2 This unit standard and unit standard 25698 replaced unit standard 2419 and unit standard 2423.
25699 Unit Standard 20 Credits
View Education Organisations with Consent to Assess »
This workplace unit standard is intended for people training to be engineering heavy fabricators. People credited with this unit standard are able to prepare to form; and form heavy fabrication materials; and inspect work after forming.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Assemble and join light fabrication materials
Version 2 This unit standard and unit standard 25701 replaced unit standard 2420 and unit standard 2424.
25700 Unit Standard 20 Credits
View Education Organisations with Consent to Assess »
This workplace unit standard is intended for people training to be engineering light fabricators. People credited with this unit standard are able to assemble and join light fabrication materials, and inspect the completed assemblies.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Assemble and join heavy fabrication materials
Version 3 This unit standard and unit standard 25700 replaced unit standard 2420 and unit standard 2424.
25701 Unit Standard 20 Credits
View Education Organisations with Consent to Assess »
This unit standard is for use in training of fabrication trades and covers assembly and joining of heavy fabrication components. People credited with this unit standard are able to: prepare, assemble and join heavy fabrication materials; and inspect the completed assemblies.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Cut light fabrication materials
This standard has expired and is no longer available.
Version 2 This unit standard and unit standard 25703 were replaced by unit standard 30272. This unit standard and unit standard 25703 replaced unit standard 2421 and unit standard 2425.
25702 Unit Standard 15 Credits
View Education Organisations with Consent to Assess »
This unit standard is for use in training of fabrication trades and covers cutting of light fabrication materials. People credited with this unit standard are able to: prepare for cutting of light fabrication materials; cut light fabrication materials; and inspect materials after cutting.
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Cut heavy fabrication materials
This standard has expired and is no longer available.
Version 2 This unit standard and unit standard 25702 were replaced by unit standard 30272. This unit standard and unit standard 25702 replaced unit standard 2421 and unit standard 2425.
25703 Unit Standard 15 Credits
View Education Organisations with Consent to Assess »
This unit standard is for use in training of fabrication trades and covers cutting of heavy fabrication materials. People credited with this unit standard are able to: prepare for cutting of heavy fabrication materials; cut heavy fabrication materials; and inspect materials after cutting.
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Develop fabrication patterns manually for complex three-dimensional objects
Version 2
25705 Unit Standard 10 Credits
View Education Organisations with Consent to Assess »
This unit standard is one in a series of pattern development and marking out unit standards for people training in engineering fabrication trades. People credited with this unit standard are able to develop fabrication patterns manually for complex three-dimensional objects.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Demonstrate and apply knowledge of advanced light fabrication trade practice
Version 2
25708 Unit Standard 12 Credits
View Education Organisations with Consent to Assess »
This unit standard, intended for off job assessment, is for experienced light fabrication trainees in the metal industries. People credited with this unit standard are able to demonstrate knowledge of advanced light fabrication trade practice; and fabricate complex objects using light fabrication materials.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Demonstrate and apply knowledge of advanced heavy fabrication trade practice
Version 2
25709 Unit Standard 12 Credits
View Education Organisations with Consent to Assess »
This unit standard is intended for off job delivery and is for experienced heavy fabrication trainees in the metal industries. People credited with this unit standard are able to demonstrate knowledge of advanced heavy fabrication trade practice; and fabricate complex objects using heavy fabrication materials.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Make up jigs and fixtures for use in engineering fabrication
Version 2
25710 Unit Standard 5 Credits
View Education Organisations with Consent to Assess »
This unit standard is intended for people training to become engineering fabricators and covers the making up of jigs and fixtures for use in locating, forming and holding fabrication components during manufacture. People credited with this unit standard are able to plan, and make-up jigs and fixtures, and test completed jigs and fixtures.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Demonstrate knowledge of pressure vessels and pressure piping for fabrication trades
Version 2
25712 Unit Standard 4 Credits
View Education Organisations with Consent to Assess »
This unit standard is for use in training of engineering metal fabrication trades. People credited with this unit standard are able to demonstrate knowledge of the requirements and terminology used in pressure equipment manufacture; pressure vessels, boilers, heat exchangers, and pressure piping.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Demonstrate knowledge of steel construction site and worksite operations, procedures and processes
Version 2
25713 Unit Standard 4 Credits
View Education Organisations with Consent to Assess »
This unit standard is for use in training of fabrication trades and covers workshop and jobsite operations, procedures, and processes related to the fabrication and assembly of steel structures. People credited with this unit standard are able to demonstrate knowledge of worksite and construction site safety procedures; demonstrate knowledge of workshop and workshop operations; demonstrate knowledge of worksite preparation for new steel constructions and alterations; and demonstrate knowledge of documentation and industry standards applicable to steel construction projects.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Lay out and mark off light fabrication shapes
This standard has expired and is no longer available.
Version 2 This unit standard and unit standard 25875 were replaced by unit standard 30440. This unit standard and unit standard 25875 replaced unit standard 2418, unit standard 2422, and unit standard 18107.
25874 Unit Standard 15 Credits
View Education Organisations with Consent to Assess »
This unit standard is for use in training of fabrication trades and covers laying out and marking off of light fabrication components. People credited with this unit standard are able to: prepare for layout and marking-off of light fabrication shapes; lay out and mark off light fabrication shapes; and inspect work after marking off and laying out.
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Lay out and mark off heavy fabrication shapes
This standard has expired and is no longer available.
Version 2 This unit standard and unit standard 25874 were replaced by unit standard 30440. This unit standard and unit standard 25874 replaced unit standard 2418, unit standard 2422, and unit standard 18107.
25875 Unit Standard 15 Credits
View Education Organisations with Consent to Assess »
This unit standard is for use in training of fabrication trades and covers laying out and marking-off of heavy fabrication components. People credited with this unit standard are able to: prepare for layout and marking off heavy fabrication shapes; lay out and mark off heavy fabrication shapes; and inspect work after marking off and laying out.
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Cut fabrication materials using machines
Version 1 This unit standard replaced unit standard 25702 and unit standard 25703.
30272 Unit Standard 10 Credits
View Education Organisations with Consent to Assess »
This workplace unit standard is intended for people training to become engineering fabricators and covers non-automated machine cutting of fabrication materials. People credited with this unit standard are able to prepare for cutting of fabrication materials; cut fabrication materials; and inspect materials after cutting.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Install steel construction structures
Version 1
31143 Unit Standard 10 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to prepare for installation of steel construction structures; install steel construction structures; and complete installation work and documentation.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Level 5
Apply knowledge of force and stress in engineering fabrications
Version 3
16957 Unit Standard 6 Credits
View Education Organisations with Consent to Assess »
This unit standard is for personnel employed in the engineering fabrication industries and covers knowledge of force and stress in fabrication. People credited with this unit standard are able to apply knowledge of force and stress in engineering fabrications.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Supervise the laying out and marking off of fabrication shapes
This standard has expired and is no longer available.
Version 7 This unit standard, unit standard 2427, unit standard 2428, and unit standard 2429 have been replaced by unit standard 26418.
2426 Unit Standard 18 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to: supervise the preparation for laying out and marking off of materials; supervise laying out and marking off of templates, sections, and surface developments for fabrication; and verify the laying out and marking off of fabrication shapes by others.
Standard-setting body:
Supervise the forming and shaping of fabrication materials
This standard has expired and is no longer available.
Version 7 This unit standard, unit standard 2426, unit standard 2428, and unit standard 2429 have been replaced by unit standard 26418.
2427 Unit Standard 20 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to: plan forming and shaping operations; supervise the non-standard forming and shaping of fabrication materials; and verify the forming and shaping of materials by others.
Standard-setting body:
Supervise assembly and mechanical joining of fabricated parts
This standard has expired and is no longer available.
Version 6 This unit standard, unit standard 2426, unit standard 2427, and unit standard 2429 have been replaced by unit standard 26418.
2428 Unit Standard 20 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to: supervise the preparation, assembly and mechanical joining of materials; and verify the assembly and mechanical joining of materials for fabrication.
Standard-setting body:
Supervise fabrication mechanical cutting operations
This standard has expired and is no longer available.
Version 7 This unit standard, unit standard 2426, unit standard 2427, and unit standard 2428 have been replaced by unit standard 26418.
2429 Unit Standard 15 Credits
View Education Organisations with Consent to Assess »
People credited with this unit standard are able to: plan mechanical cutting operations; supervise the mechanical cutting of fabrication materials; and verify the mechanical cutting of materials for fabrication.
Standard-setting body:
Supervise engineering fabrication operations
Version 1 This unit standard replaced unit standard 2426, unit standard 2427, unit standard 2428, and unit standard 2429.
26418 Unit Standard 30 Credits
View Education Organisations with Consent to Assess »
This unit standard is for supervisors with responsibility for engineering fabrication operations, preparation, personnel, machines, and inspection of products. They would typically have had training in workplace supervision and will have worked in a leading hand or in a similar role in the engineering fabrication industry. People credited with this unit standard are able to: prepare for engineering fabrication operations as a supervisor; supervise personnel in the performance of engineering fabrication operations; and inspect and document completion of engineering fabrication operations.
Consent & Moderation Requirements:
CMR 13
Standard-setting body:
Hanga-Aro-Rau Manufacturing, Engineering and Logistics Workforce Development Council
Data as at 2024-04-25 23:01:13.2